projekt:robo-workshop:programme

Beispiel-Programme und -Aufbauten

/*
  Button
 
  Turns on and off a light emitting diode(LED) connected to digital pin 13,
  when pressing a pushbutton attached to pin 2.
 
  The circuit:
  - LED attached from pin 13 to ground
  - pushbutton attached to pin 2 from +5V
  - 10K resistor attached to pin 2 from ground
 
  - Note: on most Arduinos there is already an LED on the board
    attached to pin 13.
 
  created 2005
  by DojoDave <http://www.0j0.org>
  modified 30 Aug 2011
  by Tom Igoe
 
  This example code is in the public domain.
 
  http://www.arduino.cc/en/Tutorial/Button
*/
 
int buttonPin = 2;     // the number of the pushbutton pin
int ledPin =  13;      // the number of the LED pin
 
int buttonState = 0;         // variable for reading the pushbutton status
 
void setup() {
  pinMode(ledPin, OUTPUT);
  pinMode(buttonPin, INPUT);
}
 
void loop() {
  buttonState = digitalRead(buttonPin);
 
  if (buttonState == HIGH) {
    digitalWrite(ledPin, HIGH);
  } else {
    digitalWrite(ledPin, LOW);
  }
}

#include <Servo.h>
 
Servo MeinServo;
int Position = 0;
 
void setup() {
  // put your setup code here, to run once:
  MeinServo.attach(9); // Servo hängt an Pin 9
}
 
void loop() {
  // put your main code here, to run repeatedly:
  MeinServo.write(Position);
  delay(1000);
  MeinServo.write(Position + 45);
  delay(1000);
  MeinServo.write(Position + 90);
  delay(1000);
  MeinServo.write(Position + 135);
  delay(1000);
}
#include <Servo.h>
 
// Servo dem Arduino bekannt geben
Servo servoMotor;
 
int Sensor = A0;
int DigitalPin = 7;
int SensorWert = 0;
 
 
void setup() {
  // put your setup code here, to run once:
  pinMode(DigitalPin, OUTPUT);
  Serial.begin(9600); 
 
  // Servo-Motor an Pin 9 angeschlossen
  servoMotor.attach(9);
}
 
void loop() {
  // put your main code here, to run repeatedly:
  SensorWert = analogRead(Sensor);
 
  // Trick 17 von Olaf
  digitalWrite(DigitalPin, HIGH);
  delay(SensorWert);
  digitalWrite(DigitalPin, LOW);
  delay(SensorWert);
 
  Serial.println(SensorWert, DEC);
 
  if (SensorWert < 100) {
    servoMotor.write(45);
    delay(1000);
    servoMotor.write(0);
    delay(1000);
  } 
 
  servoMotor.write(90);
}
int sensorPin = A0; // select the input pin for the potentiometer
int ledPin = 9; // select the pin for the LED
int sensorValue = 0; // variable to store the value coming from the sensor
 
void setup () 
{
  pinMode (ledPin, OUTPUT);
  Serial.begin (9600);
}
 
void loop () 
{
  sensorValue = analogRead (sensorPin);
  digitalWrite (ledPin, HIGH);
  delay (sensorValue);
  digitalWrite (ledPin, LOW);
  delay (sensorValue);
  Serial.println (sensorValue, DEC);
}
  • projekt/robo-workshop/programme.txt
  • Zuletzt geändert: vor 6 Jahren
  • von reik